FIT (名詞) →押嵌め・遊嵌・圧入
2012年05月10日
車馬駄馬田 at 08:00 | Comments(0) | fi...
目次はこちら
FIT (名詞)
$$ All of the parts of the modules 26 and the guide members 17 are formed in plastics and have sufficient resilience to allow the push-fits referred to above. / モジュール２６および案内部材１７のすべての部品は、プラスチックでつくられ、上述した押嵌めを許すのに十分な抵抗を有している。(USP6418264):押嵌め
$$ The arms 18 of the male clip attachment 17 can be pressed together to fit into an aperture in a corresponding female clip attachment... (USP5946864)
$$ The flinger device 310 may then be press-fitted onto the crankshaft 312 to a position adjacent a rear face 352 of the retainer housing and with a predetermined air gap of typically 0.5 mm. (USP5996542)
$$ As shown in FIG. 1, a pin 122 is a press fit in the chuck body 10 and cooperates with a longitudinal slot 124 (see FIG. 7) in the front sleeve 56 to prevent relative rotational movement. (USP5524909)
$$ A hole 58 is positioned at the other end of lever 48, profiled to engage in a press fit manner and rotationally fast with end 50B of pivot pin 50. (USP02073789)
$$ The headwear can be snuggly fitted to give a tight compressive fit. (USP5897581)
$$ It should be noted that the impeller 20 is a loose fit on the tubular section 46 of the rotor 40. (USP6524078):遊嵌
$$ The front grille 40 is a removable push fit onto the front baffle 20. / 前グリル４０はこの前遮蔽板２０上に押し当てることにより取り外し可能に取付けられる。(USP5402502) push fit(押し込み；押嵌め);push-fittable; <->press fit(圧入)
$$ A threaded end portion 119 secured to the pipe 118 is threaded into a plug 121 which is a force fit into the interior of the nose portion 108. / パイプ１１８に固定されねじを切った先端部１１９はプラグ１２１内にねじ込まれ、このプラグ１２１はノーズ部１０８の内部に圧入する。(USP5366528):圧入
$$ The loudspeaker unit is a demountable fit into a fixing bracket 45 which has its back walls directed at 90° to one another in conformity with the sides 14, 16 of the speaker unit. / スピーカユニット本体１０は、該本体の側面１４，１６と適合する互いに９０°をなす後壁を有する固定ブラケット４５内に着脱可能に取り付けられる。(USP5402502):取り付け
$$ Thus piston 150 is a precision fit into a bore of passageway portion 151A.(USP01025858)
$$ Again, the internal diameter of the seal is not necessarily 1mm, this diameter being chosen to be a friction fit around the fibre unit being installed, and this will vary for different fibre units.(USP5749565)
目次はこちら
FIT (名詞)
$$ All of the parts of the modules 26 and the guide members 17 are formed in plastics and have sufficient resilience to allow the push-fits referred to above. / モジュール２６および案内部材１７のすべての部品は、プラスチックでつくられ、上述した押嵌めを許すのに十分な抵抗を有している。(USP6418264):押嵌め
$$ The arms 18 of the male clip attachment 17 can be pressed together to fit into an aperture in a corresponding female clip attachment... (USP5946864)
$$ The flinger device 310 may then be press-fitted onto the crankshaft 312 to a position adjacent a rear face 352 of the retainer housing and with a predetermined air gap of typically 0.5 mm. (USP5996542)
$$ As shown in FIG. 1, a pin 122 is a press fit in the chuck body 10 and cooperates with a longitudinal slot 124 (see FIG. 7) in the front sleeve 56 to prevent relative rotational movement. (USP5524909)
$$ A hole 58 is positioned at the other end of lever 48, profiled to engage in a press fit manner and rotationally fast with end 50B of pivot pin 50. (USP02073789)
$$ The headwear can be snuggly fitted to give a tight compressive fit. (USP5897581)
$$ It should be noted that the impeller 20 is a loose fit on the tubular section 46 of the rotor 40. (USP6524078):遊嵌
$$ The front grille 40 is a removable push fit onto the front baffle 20. / 前グリル４０はこの前遮蔽板２０上に押し当てることにより取り外し可能に取付けられる。(USP5402502) push fit(押し込み；押嵌め);push-fittable; <->press fit(圧入)
$$ A threaded end portion 119 secured to the pipe 118 is threaded into a plug 121 which is a force fit into the interior of the nose portion 108. / パイプ１１８に固定されねじを切った先端部１１９はプラグ１２１内にねじ込まれ、このプラグ１２１はノーズ部１０８の内部に圧入する。(USP5366528):圧入
$$ The loudspeaker unit is a demountable fit into a fixing bracket 45 which has its back walls directed at 90° to one another in conformity with the sides 14, 16 of the speaker unit. / スピーカユニット本体１０は、該本体の側面１４，１６と適合する互いに９０°をなす後壁を有する固定ブラケット４５内に着脱可能に取り付けられる。(USP5402502):取り付け
$$ Thus piston 150 is a precision fit into a bore of passageway portion 151A.(USP01025858)
$$ Again, the internal diameter of the seal is not necessarily 1mm, this diameter being chosen to be a friction fit around the fibre unit being installed, and this will vary for different fibre units.(USP5749565)
目次はこちら
※このブログではブログの持ち主が承認した後、コメントが反映される設定です。